9
S CONTROL SYSTEMS
HARDWARE SPECIFICATIONS (Cylindrical)
Lock Body: Heavy duty Grade-1 BEST 93K series (Standard) or Schlage ND-80 series, critical latch and chassis
components are brass or corrosion-treated steel. 2 ¼
"
diameter to fit 2 ⅛
"
hole in door (conforms to ANSI A1152.2).
Material: Cold rolled steel and zinc dichromate finish for oxidation resistance with precision cast steel retractor. Lock
levers surpass BHMA standards of 450 inch-pounds of torque. 4 ¾
"
Backsets available. 2 ⅛
"
diameter bore is required.
Latch: 2 ¾
"
backset standard, brass with
9
/
16
"
throw. Housing is steel-zinc dichromate finish for oxidation resistance.
1
"
diameter bore is required.
Latch Face: Brass, bronze or stainless steel face plates. 2 ¼
"
x 1 ⅛
"
.
Strike Plate: Square corner, 1 ⅛
"
x 2 ¾
"
T strike with 1 ¼
"
lip-to-center dimension; ANSI Standard 115.3
Handing: Field reversible; Shipped right-handed
Lever handles: High quality zinc alloy. Trim components are brass or bronze. Body is approximately 1 ⅝
"
in diameter;
Handle is approximately 4 ¾
"
long (from center-line of chassis). #14 and #15 levers conform to California Administrative
Code Title 19 and Title 24. All three styles of levers conform to the Illinois Accessibility Standard.
Door Thickness: Available for 1 ¾
"
to 2 ¼
"
doors. Door thickness must be specified.
Key Cylinder: Solid brass 6 pin cylinder with two brass keys. Keyed 5 pin with Arrow ‘CS’ keyway on Arrow locks or
Schlage ‘C’ keyway with Schlage locks.
I/C Core: For use with 6 or 7 pin small or large format I/C cores (I/C cores not included)..
Finishes: 605-US3 (Polished Brass), 606-US4 (Satin Brass), 612-US10 (Satin Bronze), 613-US10B (Oil Rubbed Bronze),
625-US26 (Polished Chrome), 626-US26D (Satin Chrome) Standard. No split finishes.
Trim: Through-bolted with independent springs for each lever.
Function: Lever retracts latch bolt from either side unless the outside (cylinder side) is electrically locked. Unlocked from
the outside with valid ID code, with valid card (OM2000 only), with ID or card plus PIN (OM2000 only), or by key. Inside
always free passage.
Installation: Standard ANSI 156.2 (formerly 161) door preparation for cylindrical lockset with 2 ¾
"
backset and door stop
not greater than ¾
"
. Two anti-rotation holes required. Weatherized models require an additional ¾
"
diameter through-
door hole.
CYLINDRICAL LOCKSET CERTIFICATION
Locksets conform to the ANSI Standard 156.2, Series 4000, Grade 1 requirements.
Conforms to Federal Specs. FFH-106C, Type 161. Lever handles comply with “The
Americans With Disabilities Act of 1992”. Lockset listed to UL standards for safety
and fire (90 minutes) by Underwriters Laboratories.
The OMNILOCK Cylindrical
locks install without drilling
any holes and install in the
Standard ANSI door prep with
NO Drilling!!!
HARDWARE SPECIFICATIONS
(12 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels